SynkoElast® Primer

RubberElast® RubberElast® is a self-adhesive, tried-and-tested squeeze joint tape for secure and pressure-tight sealing of component joints between prefabricated parts. The self-adhesive RubberElast® sealing tape seals component joints in sewer and civil engineering and in hydraulic structures, among other applications. The joint sealant retains its elasticity even at low temperatures and is resistant to weathering, acids, alkalis and salt. RubberElast® can be applied quickly and without any additional aids. It is self-adhesive and is bonded to one side of a component surface. The prefabricated parts are then mounted and the RubberElast® is compressed in the component joint so that the component joint is filled. The joint is immediately watertight after compression. If precast walls are installed, the use of the BT tension lock is recommended. The combination of RubberElast® with the BT-Spannschloss® is particularly proven in flood protection. The material remains permanently elastic and thus permanently seals the joints. Installation should be carried out within a temperature range of -10 °C to +40 °C. RubberElast® retains its elasticity even at low temperatures. In addition to its very good adhesion to concrete, the squeeze joint tape also has other excellent adhesion properties, such as to metals, glass and other materials. The waterproofing tape is used in hydraulic structures, in sewer and civil engineering, and in residential and commercial construction. Advantages of the RubberElast® squeeze joint tape Pressure waterproof up to 0,5 bar Processing from -10°C to +40°C No swelling on contact with water Weather, acid, alkali and salt resistant Immediately waterproof after mounting Permanently elastic Application and possibilities of use The joint tape is used for secure and pressure-tight sealing of component joints between precast elements. Hydraulic structures (e.g. angle retaining walls in flood protection) Canal- & Civil engineering (e.g. manholes, media channels, amphibian tunnels), multi-story Residential- & commercial construction (e.g. WU basement, white tank) When using RubberElast® for sealing precast concrete joints on components made of water-impermeable concrete, in accordance with the "WU Guideline", the general test certificate issued by the building authorities must also be observed.   Technical information The substrate must be dry during installation. For difficult substrates, the additional use of RubberElast® primer is recommended. Black color Consistency elastoplastic Processing form self-adhesive on rolls with protective film Spec. density Approx. 1,3 g/cm3 Adhesive tensile strength > 60 kPa (on concrete) Max. Joint displacement Up to 7 mm for sizes 38 x 32, 48 x 42 Up to 3 mm for sizes 32 x 25, 25 x 19, 17 x 17 Temperature resistance -40°C to +60°C Working temperature -10°C to +40°C at component and material temperature Chemical resistance H2SO4(pH 4) acid, concrete attacking liquid Ca(OH)2(pH 12) alkali, NaCI salt Technical properties and variants of RubberElast® Art.-Nr. Size Joint width Wall strength 5002052 RubberElast® 17 x 17 mm 3,4 mm 8,5 cm 5002053 RubberElast® 25 x 19 mm 3,8 mm 12,5 cm 5002054 RubberElast® 32 x 25 mm 5,0 mm 16,0 cm 5002055 RubberElast® 38 x 32 mm 6,4 mm 19,0 cm 5002056 RubberElast® 48 x 42 mm 8,4 mm 24,0 cm

RubberElast® RubberElast® is a self-adhesive, tried-and-tested squeeze joint tape for secure and pressure-tight sealing of component joints between prefabricated parts. The self-adhesive RubberElast® sealing tape seals component joints in sewer and civil engineering and in hydraulic structures, among other applications. The joint sealant retains its elasticity even at low temperatures and is resistant to weathering, acids, alkalis and salt. RubberElast® can be applied quickly and without any additional aids. It is self-adhesive and is bonded to one side of a component surface. The prefabricated parts are then mounted and the RubberElast® is compressed in the component joint so that the component joint is filled. The joint is immediately watertight after compression. If precast walls are installed, the use of the BT tension lock is recommended. The combination of RubberElast® with the BT-Spannschloss® is particularly proven in flood protection. The material remains permanently elastic and thus permanently seals the joints. Installation should be carried out within a temperature range of -10 °C to +40 °C. RubberElast® retains its elasticity even at low temperatures. In addition to its very good adhesion to concrete, the squeeze joint tape also has other excellent adhesion properties, such as to metals, glass and other materials. The waterproofing tape is used in hydraulic structures, in sewer and civil engineering, and in residential and commercial construction. Advantages of the RubberElast® squeeze joint tape Pressure waterproof up to 0,5 bar Processing from -10°C to +40°C No swelling on contact with water Weather, acid, alkali and salt resistant Immediately waterproof after mounting Permanently elastic Application and possibilities of use The joint tape is used for secure and pressure-tight sealing of component joints between precast elements. Hydraulic structures (e.g. angle retaining walls in flood protection) Canal- & Civil engineering (e.g. manholes, media channels, amphibian tunnels), multi-story Residential- & commercial construction (e.g. WU basement, white tank) When using RubberElast® for sealing precast concrete joints on components made of water-impermeable concrete, in accordance with the "WU Guideline", the general test certificate issued by the building authorities must also be observed.   Technical information The substrate must be dry during installation. For difficult substrates, the additional use of RubberElast® primer is recommended. Black color Consistency elastoplastic Processing form self-adhesive on rolls with protective film Spec. density Approx. 1,3 g/cm3 Adhesive tensile strength > 60 kPa (on concrete) Max. Joint displacement Up to 7 mm for sizes 38 x 32, 48 x 42 Up to 3 mm for sizes 32 x 25, 25 x 19, 17 x 17 Temperature resistance -40°C to +60°C Working temperature -10°C to +40°C at component and material temperature Chemical resistance H2SO4(pH 4) acid, concrete attacking liquid Ca(OH)2(pH 12) alkali, NaCI salt Technical properties and variants of RubberElast® Art.-Nr. Size Joint width Wall strength 5002052 RubberElast® 17 x 17 mm 3,4 mm 8,5 cm 5002053 RubberElast® 25 x 19 mm 3,8 mm 12,5 cm 5002054 RubberElast® 32 x 25 mm 5,0 mm 16,0 cm 5002055 RubberElast® 38 x 32 mm 6,4 mm 19,0 cm 5002056 RubberElast® 48 x 42 mm 8,4 mm 24,0 cm

RubberElast® RubberElast® is a self-adhesive, tried-and-tested squeeze joint tape for secure and pressure-tight sealing of component joints between prefabricated parts. The self-adhesive RubberElast® sealing tape seals component joints in sewer and civil engineering and in hydraulic structures, among other applications. The joint sealant retains its elasticity even at low temperatures and is resistant to weathering, acids, alkalis and salt. RubberElast® can be applied quickly and without any additional aids. It is self-adhesive and is bonded to one side of a component surface. The prefabricated parts are then mounted and the RubberElast® is compressed in the component joint so that the component joint is filled. The joint is immediately watertight after compression. If precast walls are installed, the use of the BT tension lock is recommended. The combination of RubberElast® with the BT-Spannschloss® is particularly proven in flood protection. The material remains permanently elastic and thus permanently seals the joints. Installation should be carried out within a temperature range of -10 °C to +40 °C. RubberElast® retains its elasticity even at low temperatures. In addition to its very good adhesion to concrete, the squeeze joint tape also has other excellent adhesion properties, such as to metals, glass and other materials. The waterproofing tape is used in hydraulic structures, in sewer and civil engineering, and in residential and commercial construction. Advantages of the RubberElast® squeeze joint tape Pressure waterproof up to 0,5 bar Processing from -10°C to +40°C No swelling on contact with water Weather, acid, alkali and salt resistant Immediately waterproof after mounting Permanently elastic Application and possibilities of use The joint tape is used for secure and pressure-tight sealing of component joints between precast elements. Hydraulic structures (e.g. angle retaining walls in flood protection) Canal- & Civil engineering (e.g. manholes, media channels, amphibian tunnels), multi-story Residential- & commercial construction (e.g. WU basement, white tank) When using RubberElast® for sealing precast concrete joints on components made of water-impermeable concrete, in accordance with the "WU Guideline", the general test certificate issued by the building authorities must also be observed. Technical information The substrate must be dry during installation. For difficult substrates, the additional use of RubberElast® primer is recommended. Black color Consistency elastoplastic Processing form self-adhesive on rolls with protective film Spec. density Approx. 1,3 g/cm3 Adhesive tensile strength > 60 kPa (on concrete) Max. Joint displacement Up to 7 mm for sizes 38 x 32, 48 x 42 Up to 3 mm for sizes 32 x 25, 25 x 19, 17 x 17 Temperature resistance -40°C to +60°C Working temperature -10°C to +40°C at component and material temperature Chemical resistance H2SO4(pH 4) acid, concrete attacking liquid Ca(OH)2(pH 12) alkali, NaCI salt Technical properties and variants of RubberElast® Art.-Nr. Size Joint width Wall strength 5002052 RubberElast® 17 x 17 mm 3,4 mm 8,5 cm 5002053 RubberElast® 25 x 19 mm 3,8 mm 12,5 cm 5002054 RubberElast® 32 x 25 mm 5,0 mm 16,0 cm 5002055 RubberElast® 38 x 32 mm 6,4 mm 19,0 cm 5002056 RubberElast® 48 x 42 mm 8,4 mm 24,0 cm

RubberElast® RubberElast® is a self-adhesive, tried-and-tested squeeze joint tape for secure and pressure-tight sealing of component joints between prefabricated parts. The self-adhesive RubberElast® sealing tape seals component joints in sewer and civil engineering and in hydraulic structures, among other applications. The joint sealant retains its elasticity even at low temperatures and is resistant to weathering, acids, alkalis and salt. RubberElast® can be applied quickly and without any additional aids. It is self-adhesive and is bonded to one side of a component surface. The prefabricated parts are then mounted and the RubberElast® is compressed in the component joint so that the component joint is filled. The joint is immediately watertight after compression. If precast walls are installed, the use of the BT tension lock is recommended. The combination of RubberElast® with the BT-Spannschloss® is particularly proven in flood protection. The material remains permanently elastic and thus permanently seals the joints. Installation should be carried out within a temperature range of -10 °C to +40 °C. RubberElast® retains its elasticity even at low temperatures. In addition to its very good adhesion to concrete, the squeeze joint tape also has other excellent adhesion properties, such as to metals, glass and other materials. The waterproofing tape is used in hydraulic structures, in sewer and civil engineering, and in residential and commercial construction. Advantages of the RubberElast® squeeze joint tape Pressure waterproof up to 0,5 bar Processing from -10°C to +40°C No swelling on contact with water Weather, acid, alkali and salt resistant Immediately waterproof after mounting Permanently elastic Application and possibilities of use The joint tape is used for secure and pressure-tight sealing of component joints between precast elements. Hydraulic structures (e.g. angle retaining walls in flood protection) Canal- & Civil engineering (e.g. manholes, media channels, amphibian tunnels), multi-story Residential- & commercial construction (e.g. WU basement, white tank) When using RubberElast® for sealing precast concrete joints on components made of water-impermeable concrete, in accordance with the "WU Guideline", the general test certificate issued by the building authorities must also be observed. Technical information The substrate must be dry during installation. For difficult substrates, the additional use of RubberElast® primer is recommended. Black color Consistency elastoplastic Processing form self-adhesive on rolls with protective film Spec. density Approx. 1,3 g/cm3 Adhesive tensile strength > 60 kPa (on concrete) Max. Joint displacement Up to 7 mm for sizes 38 x 32, 48 x 42 Up to 3 mm for sizes 32 x 25, 25 x 19, 17 x 17 Temperature resistance -40°C to +60°C Working temperature -10°C to +40°C at component and material temperature Chemical resistance H2SO4(pH 4) acid, concrete attacking liquid Ca(OH)2(pH 12) alkali, NaCI salt Technical properties and variants of RubberElast® Art.-Nr. Size Joint width Wall strength 5002052 RubberElast® 17 x 17 mm 3,4 mm 8,5 cm 5002053 RubberElast® 25 x 19 mm 3,8 mm 12,5 cm 5002054 RubberElast® 32 x 25 mm 5,0 mm 16,0 cm 5002055 RubberElast® 38 x 32 mm 6,4 mm 19,0 cm 5002056 RubberElast® 48 x 42 mm 8,4 mm 24,0 cm

RubberElast® RubberElast® is a self-adhesive, tried-and-tested squeeze joint tape for secure and pressure-tight sealing of component joints between prefabricated parts. The self-adhesive RubberElast® sealing tape seals component joints in sewer and civil engineering and in hydraulic structures, among other applications. The joint sealant retains its elasticity even at low temperatures and is resistant to weathering, acids, alkalis and salt. RubberElast® can be applied quickly and without any additional aids. It is self-adhesive and is bonded to one side of a component surface. The prefabricated parts are then mounted and the RubberElast® is compressed in the component joint so that the component joint is filled. The joint is immediately watertight after compression. If precast walls are installed, the use of the BT tension lock is recommended. The combination of RubberElast® with the BT-Spannschloss® is particularly proven in flood protection. The material remains permanently elastic and thus permanently seals the joints. Installation should be carried out within a temperature range of -10 °C to +40 °C. RubberElast® retains its elasticity even at low temperatures. In addition to its very good adhesion to concrete, the squeeze joint tape also has other excellent adhesion properties, such as to metals, glass and other materials. The waterproofing tape is used in hydraulic structures, in sewer and civil engineering, and in residential and commercial construction. Advantages of the RubberElast® squeeze joint tape Pressure waterproof up to 0,5 bar Processing from -10°C to +40°C No swelling on contact with water Weather, acid, alkali and salt resistant Immediately waterproof after mounting Permanently elastic Application and possibilities of use The joint tape is used for secure and pressure-tight sealing of component joints between precast elements. Hydraulic structures (e.g. angle retaining walls in flood protection) Canal- & Civil engineering (e.g. manholes, media channels, amphibian tunnels), multi-story Residential- & commercial construction (e.g. WU basement, white tank) When using RubberElast® for sealing precast concrete joints on components made of water-impermeable concrete, in accordance with the "WU Guideline", the general test certificate issued by the building authorities must also be observed. Technical information The substrate must be dry during installation. For difficult substrates, the additional use of RubberElast® primer is recommended. Black color Consistency elastoplastic Processing form self-adhesive on rolls with protective film Spec. density Approx. 1,3 g/cm3 Adhesive tensile strength > 60 kPa (on concrete) Max. Joint displacement Up to 7 mm for sizes 38 x 32, 48 x 42 Up to 3 mm for sizes 32 x 25, 25 x 19, 17 x 17 Temperature resistance -40°C to +60°C Working temperature -10°C to +40°C at component and material temperature Chemical resistance H2SO4(pH 4) acid, concrete attacking liquid Ca(OH)2(pH 12) alkali, NaCI salt Technical properties and variants of RubberElast® Art.-Nr. Size Joint width Wall strength 5002052 RubberElast® 17 x 17 mm 3,4 mm 8,5 cm 5002053 RubberElast® 25 x 19 mm 3,8 mm 12,5 cm 5002054 RubberElast® 32 x 25 mm 5,0 mm 16,0 cm 5002055 RubberElast® 38 x 32 mm 6,4 mm 19,0 cm 5002056 RubberElast® 48 x 42 mm 8,4 mm 24,0 cm