The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary buildings Advantages Dry screw connection Without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even in low temperatures or precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN] Shear force, perpendicular to the fastener axis VR,d [kN] M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spanschloss® Art.-Nr. Article description Article information 4009082 BT Spannschloss® M12 galvanised 2.000 pieces / pallet 4009076 BT Spannschloss® M16 galvanised 850 pieces / pallet 4009075 BT Spannschloss® M20 galvanised 600 pieces / pallet 4009079 BT Spannschloss® M12 stainless steel interlocked 4009080 BT Spannschloss® M16 stainless steel interlocked 4009081 BT Spannschloss® M20 stainless steel interlocked 4009086 BT-Spannschloss® M12 galvanised Set 20 sets in a box 4009074 BT-Spannschloss® M16 galvanised Set 10 sets in a box 4009072 BT-Spannschloss® M20 galvanised Set 10 sets in a box 4009084 BT-Spannschloss® M12 stainless steel set 10 sets in a box 4009083 BT-Spannschloss® M16 stainless steel set 10 sets in a box 4009085 BT-Spannschloss® M20 stainless steel set 8 sets in a box 4009123 BT-Spannschloss® Starter Set M16 for testing the turnbuckle system 4009152 BT-Spannschloss® Starter Set M20 for testing the turnbuckle system NOTE: EACH BT TURNBUCKLE® SET CONSISTS OF A BT TURNBUCKLE® IN THE CORRESPONDING VERSION AND TWO MATCHING SCREWS AND WASHERS.
The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible DThree-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary structures Advantages Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN]. Shear force, perpendicular to the fastener axis VR,d [kN]. M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spannschloss® - Set Art.-Nr. Product Description Information 4009086 BT-Spannschloss® M12 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - 8.8 - tZn) 2 pcs. washer (ISO 7093 - 1-12-200 HV - tZn) for wall thicknesses > 6 cm ETA-19/0013 4009084 BT-Spannschloss® M12 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - A4-70) 2 pcs. washer (ISO 7093-1 - 12 - 200 HV - A4) for wall thicknesses > 6 cm 4009074 BT-Spannschloss® M16 galvanised, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - 8.8 - tZn) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - tZn) for wall thicknesses > 12 cm ETA-19/0013 4009083 BT-Spannschloss® M16 stainless steel, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - A4-70) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - A4-70) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - A4) for wall thicknesses > 12 cm 4009072 BT-Spannschloss® M20 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - tZn) for wall thicknesses > 14 cm ETA-19/0013 4009085 BT-Spannschloss® M20 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - A4-70) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - A4) for wall thicknesses > 14 cm 4009123 BT-Spannschloss® Starter Set M16 incl.: 6x BT-Spannschloss® M16 galvanised, 6x M16 x 50 screws, 6x M16 x 40 screws, 12x washers M16, 12x T-Fixx anchor M16x100 free of charge: 1x ratchet combination spanner 24 mm, 6x one-way recess body, 6x nail plate M16 4009152 BT-Spannschloss® Starter Set M20 incl.: 6x BT-Spannschloss® M20 galvanised, 12x M20 x 60 screws, 12x washers M20, 12x T-Fixx anchor M20 free of charge: 1x ratchet combination spanner 30 mm, 6x one-way recess body, 6x nail plate M20
BT-Spannschloss® Set (BT-Turnbuckle) The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible DThree-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary structures Advantages Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN]. Shear force, perpendicular to the fastener axis VR,d [kN]. M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spannschloss® - Set Art.-Nr. Product Description Information 4009086 BT-Spannschloss® M12 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - 8.8 - tZn) 2 pcs. washer (ISO 7093 - 1-12-200 HV - tZn) for wall thicknesses > 6 cm ETA-19/0013 4009084 BT-Spannschloss® M12 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - A4-70) 2 pcs. washer (ISO 7093-1 - 12 - 200 HV - A4) for wall thicknesses > 6 cm 4009074 BT-Spannschloss® M16 galvanised, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - 8.8 - tZn) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - tZn) for wall thicknesses > 12 cm ETA-19/0013 4009083 BT-Spannschloss® M16 stainless steel, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - A4-70) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - A4-70) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - A4) for wall thicknesses > 12 cm 4009072 BT-Spannschloss® M20 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - tZn) for wall thicknesses > 14 cm ETA-19/0013 4009085 BT-Spannschloss® M20 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - A4-70) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - A4) for wall thicknesses > 14 cm 4009123 BT-Spannschloss® Starter Set M16 incl.: 6x BT-Spannschloss® M16 galvanised, 6x M16 x 50 screws, 6x M16 x 40 screws, 12x washers M16, 12x T-Fixx anchor M16x100 free of charge: 1x ratchet combination spanner 24 mm, 6x one-way recess body, 6x nail plate M16 4009152 BT-Spannschloss® Starter Set M20 incl.: 6x BT-Spannschloss® M20 galvanised, 12x M20 x 60 screws, 12x washers M20, 12x T-Fixx anchor M20 free of charge: 1x ratchet combination spanner 30 mm, 6x one-way recess body, 6x nail plate M20
The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary buildings Advantages Dry screw connection Without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even in low temperatures or precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN] Shear force, perpendicular to the fastener axis VR,d [kN] M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spanschloss® Art.-Nr. Article description Article information 4009082 BT Spannschloss® M12 galvanised 2.000 pieces / pallet 4009076 BT Spannschloss® M16 galvanised 850 pieces / pallet 4009075 BT Spannschloss® M20 galvanised 600 pieces / pallet 4009079 BT Spannschloss® M12 stainless steel interlocked 4009080 BT Spannschloss® M16 stainless steel interlocked 4009081 BT Spannschloss® M20 stainless steel interlocked 4009086 BT-Spannschloss® M12 galvanised Set 20 sets in a box 4009074 BT-Spannschloss® M16 galvanised Set 10 sets in a box 4009072 BT-Spannschloss® M20 galvanised Set 10 sets in a box 4009084 BT-Spannschloss® M12 stainless steel set 10 sets in a box 4009083 BT-Spannschloss® M16 stainless steel set 10 sets in a box 4009085 BT-Spannschloss® M20 stainless steel set 8 sets in a box 4009123 BT-Spannschloss® Starter Set M16 for testing the turnbuckle system 4009152 BT-Spannschloss® Starter Set M20 for testing the turnbuckle system NOTE: EACH BT TURNBUCKLE® SET CONSISTS OF A BT TURNBUCKLE® IN THE CORRESPONDING VERSION AND TWO MATCHING SCREWS AND WASHERS.
The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary buildings Advantages Dry screw connection Without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even in low temperatures or precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN] Shear force, perpendicular to the fastener axis VR,d [kN] M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spanschloss® Art.-Nr. Article description Article information 4009082 BT Spannschloss® M12 galvanised 2.000 pieces / pallet 4009076 BT Spannschloss® M16 galvanised 850 pieces / pallet 4009075 BT Spannschloss® M20 galvanised 600 pieces / pallet 4009079 BT Spannschloss® M12 stainless steel interlocked 4009080 BT Spannschloss® M16 stainless steel interlocked 4009081 BT Spannschloss® M20 stainless steel interlocked 4009086 BT-Spannschloss® M12 galvanised Set 20 sets in a box 4009074 BT-Spannschloss® M16 galvanised Set 10 sets in a box 4009072 BT-Spannschloss® M20 galvanised Set 10 sets in a box 4009084 BT-Spannschloss® M12 stainless steel set 10 sets in a box 4009083 BT-Spannschloss® M16 stainless steel set 10 sets in a box 4009085 BT-Spannschloss® M20 stainless steel set 8 sets in a box 4009123 BT-Spannschloss® Starter Set M16 for testing the turnbuckle system 4009152 BT-Spannschloss® Starter Set M20 for testing the turnbuckle system NOTE: EACH BT TURNBUCKLE® SET CONSISTS OF A BT TURNBUCKLE® IN THE CORRESPONDING VERSION AND TWO MATCHING SCREWS AND WASHERS.
The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible DThree-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary structures Advantages Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN]. Shear force, perpendicular to the fastener axis VR,d [kN]. M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spannschloss® - Set Art.-Nr. Product Description Information 4009086 BT-Spannschloss® M12 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - 8.8 - tZn) 2 pcs. washer (ISO 7093 - 1-12-200 HV - tZn) for wall thicknesses > 6 cm ETA-19/0013 4009084 BT-Spannschloss® M12 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - A4-70) 2 pcs. washer (ISO 7093-1 - 12 - 200 HV - A4) for wall thicknesses > 6 cm 4009074 BT-Spannschloss® M16 galvanised, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - 8.8 - tZn) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - tZn) for wall thicknesses > 12 cm ETA-19/0013 4009083 BT-Spannschloss® M16 stainless steel, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - A4-70) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - A4-70) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - A4) for wall thicknesses > 12 cm 4009072 BT-Spannschloss® M20 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - tZn) for wall thicknesses > 14 cm ETA-19/0013 4009085 BT-Spannschloss® M20 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - A4-70) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - A4) for wall thicknesses > 14 cm 4009123 BT-Spannschloss® Starter Set M16 incl.: 6x BT-Spannschloss® M16 galvanised, 6x M16 x 50 screws, 6x M16 x 40 screws, 12x washers M16, 12x T-Fixx anchor M16x100 free of charge: 1x ratchet combination spanner 24 mm, 6x one-way recess body, 6x nail plate M16 4009152 BT-Spannschloss® Starter Set M20 incl.: 6x BT-Spannschloss® M20 galvanised, 12x M20 x 60 screws, 12x washers M20, 12x T-Fixx anchor M20 free of charge: 1x ratchet combination spanner 30 mm, 6x one-way recess body, 6x nail plate M20
The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible DThree-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary structures Advantages Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN]. Shear force, perpendicular to the fastener axis VR,d [kN]. M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spannschloss® - Set Art.-Nr. Product Description Information 4009086 BT-Spannschloss® M12 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - 8.8 - tZn) 2 pcs. washer (ISO 7093 - 1-12-200 HV - tZn) for wall thicknesses > 6 cm ETA-19/0013 4009084 BT-Spannschloss® M12 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - A4-70) 2 pcs. washer (ISO 7093-1 - 12 - 200 HV - A4) for wall thicknesses > 6 cm 4009074 BT-Spannschloss® M16 galvanised, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - 8.8 - tZn) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - tZn) for wall thicknesses > 12 cm ETA-19/0013 4009083 BT-Spannschloss® M16 stainless steel, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - A4-70) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - A4-70) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - A4) for wall thicknesses > 12 cm 4009072 BT-Spannschloss® M20 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - tZn) for wall thicknesses > 14 cm ETA-19/0013 4009085 BT-Spannschloss® M20 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - A4-70) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - A4) for wall thicknesses > 14 cm 4009123 BT-Spannschloss® Starter Set M16 incl.: 6x BT-Spannschloss® M16 galvanised, 6x M16 x 50 screws, 6x M16 x 40 screws, 12x washers M16, 12x T-Fixx anchor M16x100 free of charge: 1x ratchet combination spanner 24 mm, 6x one-way recess body, 6x nail plate M16 4009152 BT-Spannschloss® Starter Set M20 incl.: 6x BT-Spannschloss® M20 galvanised, 12x M20 x 60 screws, 12x washers M20, 12x T-Fixx anchor M20 free of charge: 1x ratchet combination spanner 30 mm, 6x one-way recess body, 6x nail plate M20
The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible DThree-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary structures Advantages Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN]. Shear force, perpendicular to the fastener axis VR,d [kN]. M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spannschloss® - Set Art.-Nr. Product Description Information 4009086 BT-Spannschloss® M12 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - 8.8 - tZn) 2 pcs. washer (ISO 7093 - 1-12-200 HV - tZn) for wall thicknesses > 6 cm ETA-19/0013 4009084 BT-Spannschloss® M12 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M12 x 40 - A4-70) 2 pcs. washer (ISO 7093-1 - 12 - 200 HV - A4) for wall thicknesses > 6 cm 4009074 BT-Spannschloss® M16 galvanised, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - 8.8 - tZn) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - tZn) for wall thicknesses > 12 cm ETA-19/0013 4009083 BT-Spannschloss® M16 stainless steel, set incl.: 1 pcs. hexagon head screw (ISO 4017 - M16 x 40 - A4-70) 1 pcs. hexagon head screw (ISO 4017 - M16 x 50 - A4-70) 2 pcs. washer (ISO 7093-1 - 16 - 200 HV - A4) for wall thicknesses > 12 cm 4009072 BT-Spannschloss® M20 galvanised, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - 8.8 - tZn) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - tZn) for wall thicknesses > 14 cm ETA-19/0013 4009085 BT-Spannschloss® M20 stainless steel, set incl.: 2 pcs. hexagon head screw (ISO 4017 - M20 x 60 - A4-70) 2 pcs. washer (ISO 7093-1 - 20 - 200 HV - A4) for wall thicknesses > 14 cm 4009123 BT-Spannschloss® Starter Set M16 incl.: 6x BT-Spannschloss® M16 galvanised, 6x M16 x 50 screws, 6x M16 x 40 screws, 12x washers M16, 12x T-Fixx anchor M16x100 free of charge: 1x ratchet combination spanner 24 mm, 6x one-way recess body, 6x nail plate M16 4009152 BT-Spannschloss® Starter Set M20 incl.: 6x BT-Spannschloss® M20 galvanised, 12x M20 x 60 screws, 12x washers M20, 12x T-Fixx anchor M20 free of charge: 1x ratchet combination spanner 30 mm, 6x one-way recess body, 6x nail plate M20
The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary buildings Advantages Dry screw connection Without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even in low temperatures or precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN] Shear force, perpendicular to the fastener axis VR,d [kN] M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spanschloss® Art.-Nr. Article description Article information 4009082 BT Spannschloss® M12 galvanised 2.000 pieces / pallet 4009076 BT Spannschloss® M16 galvanised 850 pieces / pallet 4009075 BT Spannschloss® M20 galvanised 600 pieces / pallet 4009079 BT Spannschloss® M12 stainless steel interlocked 4009080 BT Spannschloss® M16 stainless steel interlocked 4009081 BT Spannschloss® M20 stainless steel interlocked 4009086 BT-Spannschloss® M12 galvanised Set 20 sets in a box 4009074 BT-Spannschloss® M16 galvanised Set 10 sets in a box 4009072 BT-Spannschloss® M20 galvanised Set 10 sets in a box 4009084 BT-Spannschloss® M12 stainless steel set 10 sets in a box 4009083 BT-Spannschloss® M16 stainless steel set 10 sets in a box 4009085 BT-Spannschloss® M20 stainless steel set 8 sets in a box 4009123 BT-Spannschloss® Starter Set M16 for testing the turnbuckle system 4009152 BT-Spannschloss® Starter Set M20 for testing the turnbuckle system NOTE: EACH BT TURNBUCKLE® SET CONSISTS OF A BT TURNBUCKLE® IN THE CORRESPONDING VERSION AND TWO MATCHING SCREWS AND WASHERS.
The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary buildings Advantages Dry screw connection Without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even in low temperatures or precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN] Shear force, perpendicular to the fastener axis VR,d [kN] M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spanschloss® Art.-Nr. Article description Article information 4009082 BT Spannschloss® M12 galvanised 2.000 pieces / pallet 4009076 BT Spannschloss® M16 galvanised 850 pieces / pallet 4009075 BT Spannschloss® M20 galvanised 600 pieces / pallet 4009079 BT Spannschloss® M12 stainless steel interlocked 4009080 BT Spannschloss® M16 stainless steel interlocked 4009081 BT Spannschloss® M20 stainless steel interlocked 4009086 BT-Spannschloss® M12 galvanised Set 20 sets in a box 4009074 BT-Spannschloss® M16 galvanised Set 10 sets in a box 4009072 BT-Spannschloss® M20 galvanised Set 10 sets in a box 4009084 BT-Spannschloss® M12 stainless steel set 10 sets in a box 4009083 BT-Spannschloss® M16 stainless steel set 10 sets in a box 4009085 BT-Spannschloss® M20 stainless steel set 8 sets in a box 4009123 BT-Spannschloss® Starter Set M16 for testing the turnbuckle system 4009152 BT-Spannschloss® Starter Set M20 for testing the turnbuckle system NOTE: EACH BT TURNBUCKLE® SET CONSISTS OF A BT TURNBUCKLE® IN THE CORRESPONDING VERSION AND TWO MATCHING SCREWS AND WASHERS.
BT Turnbuckle® - M16 Set PHILIPP PB Anchor 1 Set consists of: 1 piece BT Turnbuckle M16 – galvanized 1 piece Screw M16x40 – DIN 933 / ISO 4017 – 8.8 – galvanized 1 piece Screw M16x50 – DIN 933 / ISO 4017 – 8.8 – galvanized 2 pieces Washers M16 – DIN 125 – galvanized 2 pieces PHILIPP PB Anchors 16 x 115 mm galvanizedApproval: ETA-19/0013 These approved, high-load capacity internal thread anchors in five different sizes (RD12-30) can be used wherever load-bearing structures need to be subsequently connected to precast reinforced concrete or cast-in-place concrete elements. Whether in reinforced/unreinforced or cracked/uncracked standard concrete, the PB system reliably and permanently transfers tensile and shear loads or combinations thereof. Various installation options (flush or recessed) and material variants (galvanized or stainless steel) enable a wide range of applications. Product Features Approved system (ETA certification) Versatile, durable fastening of all types of constructions Flexible formwork installation – recessed or flush Simple, software-based design according to DIN EN 1992-4:2019-04 Fields of Application Balcony railings, stair railings Bridge railings Stadium seating Façade constructions Pipeline and utility route constructions Connection of steel/wood constructions to concrete Technical Properties and Variants of the BT Turnbuckle® - Set PHILIPP PB Anchor Art. No. Product Description 4009237 BT Turnbuckle® M16 - Set, galv. + PB Anchor 16 x 115 10 sets / box; 500 sets / pallet 4009238 BT Turnbuckle® M20 - Set, galv. + PB Anchor 20 x 155 10 sets / box; 500 sets / pallet
BT Turnbuckle® - M20 Set PHILIPP PB Anchor 1 Set consists of: 1 piece BT Turnbuckle M20 – galvanized 2 pieces Screws M20x60 – DIN 933 / ISO 4017 – 8.8 – galvanized 2 pieces Washers M20 – DIN 125 – galvanized 2 pieces PB Anchors 20 x 155 These approved, high-load capacity internal thread anchors in five different sizes (RD12-30) can be used wherever load-bearing structures need to be subsequently connected to precast reinforced concrete or cast-in-place concrete elements. Whether used in reinforced/unreinforced or cracked/uncracked normal concrete, the PB system safely and permanently transfers tensile and shear loads or combinations thereof. Various installation options (flush or recessed) and materials (galvanized or stainless steel versions) enable a wide range of applications. Product Features Approved system (ETA certification) Versatile, durable fastening of all kinds of structures Flexible formwork installation – recessed or flush Simple, software-based calculation according to DIN EN 1992-4:2019-04 Fields of Application Balcony railings, stair railings Bridge railings Stadium seating Façade constructions Pipeline and utility route constructions Connection of steel/wood structures to concrete Technical Properties and Variants of the BT Turnbuckle® - Set PHILIPP PB Anchor Art. No. Product Description 4009237 BT Turnbuckle® M16 - Set, galv. + PB Anchor 16 x 115 10 sets / box; 500 sets / pallet 4009238 BT Turnbuckle® M20 - Set, galv. + PB Anchor 20 x 155 10 sets / box; 500 sets / pallet
BT-Spannschloss® (BT-Turnbuckle) M12 galvanised The BT-Spannschloss® is part of an easy-to-use connection system - without any further additional materials or aids. The BT-Spannschloss® enables rational and precise assemblies as well as permanent connections of precast concrete elements. By using the BT-Spannschloss® and corresponding fasteners, precast elements can be connected to each other without a mineral grout. This eliminates curing times and weather-related downtimes. In addition, the BT-Spannschloss® can also be used at low temperatures and can be fully loaded immediately. The building authority approval (Z-14.4-599) certifies the reliability of the product. The BT-Spannschloss® is offered in three sizes - M12, M16 and M20 - and is available in galvanised or stainless steel finishes. Product features Dry screw connection without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even at low temperatures or during precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Areas of application Angle retaining walls in flood protection Residential and commercial construction Agricultural facilities (e.g. biogas plants, silos) Sewer and civil engineering (e.g. manholes, media channels, amphibian tunnels) Temporary buildings Advantages Dry screw connection Without grouting, without special tools Immediately loadable, no curing times Weather-independent installation even in low temperatures or precipitation Can be dismantled - deconstruction of temporarily erected structures possible Three-point connection possible Load capacity (rated resistors) Design values for the tensile load-bearing capacity (limit tensile force) and for the shear force capacity (limit shear force) according to DIBt approval Z-14.4-599. The design values for the tensile load capacity (limit tensile force) NR,d and for the shear force capacity (limit tensile force) VR,d can be taken from the following table: BT-Spannschloss® Tensile force, in the direction of the fastener axis NR,d [kN] Shear force, perpendicular to the fastener axis VR,d [kN] M12 33,7 9,4 M16 43,5 26,2 M20 52,5 24,8 Combined load from tensile and shear forces In the case of combined loading due to the design values of the acting tensile forces and shear forces, an interaction check must be carried out. Technical features and variants of the BT-Spanschloss® Art.-Nr. Article description Article information 4009082 BT Spannschloss® M12 galvanised 2.000 pieces / pallet 4009076 BT Spannschloss® M16 galvanised 850 pieces / pallet 4009075 BT Spannschloss® M20 galvanised 600 pieces / pallet 4009079 BT Spannschloss® M12 stainless steel interlocked 4009080 BT Spannschloss® M16 stainless steel interlocked 4009081 BT Spannschloss® M20 stainless steel interlocked 4009086 BT-Spannschloss® M12 galvanised Set 20 sets in a box 4009074 BT-Spannschloss® M16 galvanised Set 10 sets in a box 4009072 BT-Spannschloss® M20 galvanised Set 10 sets in a box 4009084 BT-Spannschloss® M12 stainless steel set 10 sets in a box 4009083 BT-Spannschloss® M16 stainless steel set 10 sets in a box 4009085 BT-Spannschloss® M20 stainless steel set 8 sets in a box 4009123 BT-Spannschloss® Starter Set M16 for testing the turnbuckle system 4009152 BT-Spannschloss® Starter Set M20 for testing the turnbuckle system NOTE: EACH BT TURNBUCKLE® SET CONSISTS OF A BT TURNBUCKLE® IN THE CORRESPONDING VERSION AND TWO MATCHING SCREWS AND WASHERS.
DoWaTherm Technical features and variants of DoWaTherm Art.-Nr. Article description Article information 1008157 DoWaTherm 08/200 with 2-hole foot* plugged 600 pieces / carton; 4.800 pieces / pallet 1008158 DoWaTherm 08/240 with 2-hole foot* plugged 500 pieces / carton; 4.000 pieces / pallet*Product outlet!
Facade anchor FD-2 The FD-2 facade anchor is used for fastening thermal insulation to exterior building walls with facade systems. Particularly noteworthy is its universal applicability, i.e. a suitable anchor size can be found for any thickness of thermal insulation. For soft thermal insulation materials, a washer with a diameter of 100 mm is used. Technical characteristics and variants of The Facade Anchor FD-2 Art.-Nr. Article description Article information Selling price 3007060 Facade anchor FD-2 Anchor 50 L = 50 mm, 500 pieces / box on request 3007059 Facade anchor FD-2 anchor 100 L= 100 mm, 500 pieces / box on request 3007062 Facade anchor FD-2 GRP dowel rod 5,5/300 Ø 5,5 mm, L = 300 mm on request 3007063 Facade anchor FD-2 GRP dowel rod 5,5/350 Ø 5,5 mm, L = 350 mm on request 3007057 Facade anchor FD-2 GRP dowel rod 5,5/400 Ø 5,5 mm, L = 400 mm on request 3007081 Facade anchor FD-2 GRP dowel rod 5,5/450 Ø 5,5 mm, L = 450 mm on request 3007082 Facade anchor FD-2 GRP dowel rod 5,5/500 Ø 5,5 mm, L = 500 mm on request 3007058 Facade anchor plastic plate PE60 Ø 60 mm, 500 pieces/box on request* other versions on request
Facade anchor FD-2 The FD-2 facade anchor is used for fastening thermal insulation to exterior building walls with facade systems. Particularly noteworthy is its universal applicability, i.e. a suitable anchor size can be found for any thickness of thermal insulation. For soft thermal insulation materials, a washer with a diameter of 100 mm is used. Technical characteristics and variants of The Facade Anchor FD-2 Art.-Nr. Article description Article information Selling price 3007060 Facade anchor FD-2 Anchor 50 L = 50 mm, 500 pieces / box on request 3007059 Facade anchor FD-2 anchor 100 L= 100 mm, 500 pieces / box on request 3007062 Facade anchor FD-2 GRP dowel rod 5,5/300 Ø 5,5 mm, L = 300 mm on request 3007063 Facade anchor FD-2 GRP dowel rod 5,5/350 Ø 5,5 mm, L = 350 mm on request 3007057 Facade anchor FD-2 GRP dowel rod 5,5/400 Ø 5,5 mm, L = 400 mm on request 3007081 Facade anchor FD-2 GRP dowel rod 5,5/450 Ø 5,5 mm, L = 450 mm on request 3007082 Facade anchor FD-2 GRP dowel rod 5,5/500 Ø 5,5 mm, L = 500 mm on request 3007058 Facade anchor plastic plate PE60 Ø 60 mm, 500 pieces/box on request* other versions on request
Facade anchor FD-2 The FD-2 facade anchor is used for fastening thermal insulation to exterior building walls with facade systems. Particularly noteworthy is its universal applicability, i.e. a suitable anchor size can be found for any thickness of thermal insulation. For soft thermal insulation materials, a washer with a diameter of 100 mm is used. Technical characteristics and variants of The Facade Anchor FD-2 Art.-Nr. Article description Article information Selling price 3007060 Facade anchor FD-2 Anchor 50 L = 50 mm, 500 pieces / box on request 3007059 Facade anchor FD-2 anchor 100 L= 100 mm, 500 pieces / box on request 3007062 Facade anchor FD-2 GRP dowel rod 5,5/300 Ø 5,5 mm, L = 300 mm on request 3007063 Facade anchor FD-2 GRP dowel rod 5,5/350 Ø 5,5 mm, L = 350 mm on request 3007057 Facade anchor FD-2 GRP dowel rod 5,5/400 Ø 5,5 mm, L = 400 mm on request 3007081 Facade anchor FD-2 GRP dowel rod 5,5/450 Ø 5,5 mm, L = 450 mm on request 3007082 Facade anchor FD-2 GRP dowel rod 5,5/500 Ø 5,5 mm, L = 500 mm on request 3007058 Facade anchor plastic plate PE60 Ø 60 mm, 500 pieces/box on request* other versions on request
Facade anchor FD-2 The FD-2 facade anchor is used for fastening thermal insulation to exterior building walls with facade systems. Particularly noteworthy is its universal applicability, i.e. a suitable anchor size can be found for any thickness of thermal insulation. For soft thermal insulation materials, a washer with a diameter of 100 mm is used. Technical characteristics and variants of The Facade Anchor FD-2 Art.-Nr. Article description Article information Selling price 3007060 Facade anchor FD-2 Anchor 50 L = 50 mm, 500 pieces / box on request 3007059 Facade anchor FD-2 anchor 100 L= 100 mm, 500 pieces / box on request 3007062 Facade anchor FD-2 GRP dowel rod 5,5/300 Ø 5,5 mm, L = 300 mm on request 3007063 Facade anchor FD-2 GRP dowel rod 5,5/350 Ø 5,5 mm, L = 350 mm on request 3007057 Facade anchor FD-2 GRP dowel rod 5,5/400 Ø 5,5 mm, L = 400 mm on request 3007081 Facade anchor FD-2 GRP dowel rod 5,5/450 Ø 5,5 mm, L = 450 mm on request 3007082 Facade anchor FD-2 GRP dowel rod 5,5/500 Ø 5,5 mm, L = 500 mm on request 3007058 Facade anchor plastic plate PE60 Ø 60 mm, 500 pieces/box on request* other versions on request
Facade anchor FD-2 The FD-2 facade anchor is used for fastening thermal insulation to exterior building walls with facade systems. Particularly noteworthy is its universal applicability, i.e. a suitable anchor size can be found for any thickness of thermal insulation. For soft thermal insulation materials, a washer with a diameter of 100 mm is used. Technical characteristics and variants of The Facade Anchor FD-2 Art.-Nr. Article description Article information Selling price 3007060 Facade anchor FD-2 Anchor 50 L = 50 mm, 500 pieces / box on request 3007059 Facade anchor FD-2 anchor 100 L= 100 mm, 500 pieces / box on request 3007062 Facade anchor FD-2 GRP dowel rod 5,5/300 Ø 5,5 mm, L = 300 mm on request 3007063 Facade anchor FD-2 GRP dowel rod 5,5/350 Ø 5,5 mm, L = 350 mm on request 3007057 Facade anchor FD-2 GRP dowel rod 5,5/400 Ø 5,5 mm, L = 400 mm on request 3007081 Facade anchor FD-2 GRP dowel rod 5,5/450 Ø 5,5 mm, L = 450 mm on request 3007082 Facade anchor FD-2 GRP dowel rod 5,5/500 Ø 5,5 mm, L = 500 mm on request 3007058 Facade anchor plastic plate PE60 Ø 60 mm, 500 pieces/box on request* other versions on request
Facade anchor FD-2 The FD-2 facade anchor is used for fastening thermal insulation to exterior building walls with facade systems. Particularly noteworthy is its universal applicability, i.e. a suitable anchor size can be found for any thickness of thermal insulation. For soft thermal insulation materials, a washer with a diameter of 100 mm is used. Technical characteristics and variants of The Facade Anchor FD-2 Art.-Nr. Article description Article information Selling price 3007060 Facade anchor FD-2 Anchor 50 L = 50 mm, 500 pieces / box on request 3007059 Facade anchor FD-2 anchor 100 L= 100 mm, 500 pieces / box on request 3007062 Facade anchor FD-2 GRP dowel rod 5,5/300 Ø 5,5 mm, L = 300 mm on request 3007063 Facade anchor FD-2 GRP dowel rod 5,5/350 Ø 5,5 mm, L = 350 mm on request 3007057 Facade anchor FD-2 GRP dowel rod 5,5/400 Ø 5,5 mm, L = 400 mm on request 3007081 Facade anchor FD-2 GRP dowel rod 5,5/450 Ø 5,5 mm, L = 450 mm on request 3007082 Facade anchor FD-2 GRP dowel rod 5,5/500 Ø 5,5 mm, L = 500 mm on request 3007058 Facade anchor plastic plate PE60 Ø 60 mm, 500 pieces/box on request* other versions on request
GFRP spacer bar The GFRP spacer is a profiled rod made of glass fiber reinforced plastic (GFRP). The spacer guarantees dimensionally accurate production of core-insulated double walls. Due to the profiling, the rod achieves high pull-out and punch-through resistances. The ends of the rod are partially injected so that the ends are tapered, but the rod still has a centric bearing surface and thus does not buckle laterally. The centric loading means that the spacer does not deform in height and no oversize has to be planned. Furthermore, the taper at the end serves a quick and easy penetration into the fresh concrete, as larger aggregates are simply pushed aside. The surface visibility of the bars is almost non-existent due to the taper at the end. The bar has a high resistance to alkalis. Benefits energy efficient - thermal bridge free adjustment of wall thicknesses powerful - high tear-out and punching resistance due to profiling Cost-effective - low assembly costs due to quick and easy installation compatible - perfect complement to the ThermoPin® Applications core insulated double walls Residential & commercial construction, single or multi-storey Technical characteristics and variants of the GFRP spacer bar Art.-Nr. Product Diameter Description 3009225 GFRP spacer bar 300 mm profiled 12 mm Spacer for core-insulated double walls with 300 mm wall thickness 3009226 GFRP spacer bar 350 mm profiled 12 mm Spacer for core-insulated double walls with 350 mm wall thickness 3009224 GFRP spacer bar 360 mm profiled 12 mm Spacer for core-insulated double walls with 360 mm wall thickness 3009318 GFRP spacer bar 365 mm profiled 12 mm Spacer for core-insulated double walls with 365 mm wall thickness 3009223 GFRP spacer bar 400 mm profiled 12 mm Spacer for core-insulated double walls with 400 mm wall thickness 3009321 GFRP spacer bar 420 mm profiled 12 mm Spacer for core-insulated double walls with 420 mm wall thickness 3009276 GFRP spacer bar 440 mm profiled 12 mm Spacer for core-insulated double walls with 440 mm wall thickness 3009277 GFRP spacer bar 500 mm profiled 12 mm Spacer for core-insulated double walls with 500 mm wall thickness Special lengths on request
GFRP spacer bar The GFRP spacer is a profiled rod made of glass fiber reinforced plastic (GFRP). The spacer guarantees dimensionally accurate production of core-insulated double walls. Due to the profiling, the rod achieves high pull-out and punch-through resistances. The ends of the rod are partially injected so that the ends are tapered, but the rod still has a centric bearing surface and thus does not buckle laterally. The centric loading means that the spacer does not deform in height and no oversize has to be planned. Furthermore, the taper at the end serves a quick and easy penetration into the fresh concrete, as larger aggregates are simply pushed aside. The surface visibility of the bars is almost non-existent due to the taper at the end. The bar has a high resistance to alkalis. Benefits energy efficient - thermal bridge free adjustment of wall thicknesses powerful - high tear-out and punching resistance due to profiling Cost-effective - low assembly costs due to quick and easy installation compatible - perfect complement to the ThermoPin® Applications core insulated double walls Residential & commercial construction, single or multi-storey Technical characteristics and variants of the GFRP spacer bar Art.-Nr. Product Diameter Description 3009225 GFRP spacer bar 300 mm profiled 12 mm Spacer for core-insulated double walls with 300 mm wall thickness 3009226 GFRP spacer bar 350 mm profiled 12 mm Spacer for core-insulated double walls with 350 mm wall thickness 3009224 GFRP spacer bar 360 mm profiled 12 mm Spacer for core-insulated double walls with 360 mm wall thickness 3009318 GFRP spacer bar 365 mm profiled 12 mm Spacer for core-insulated double walls with 365 mm wall thickness 3009223 GFRP spacer bar 400 mm profiled 12 mm Spacer for core-insulated double walls with 400 mm wall thickness 3009321 GFRP spacer bar 420 mm profiled 12 mm Spacer for core-insulated double walls with 420 mm wall thickness 3009276 GFRP spacer bar 440 mm profiled 12 mm Spacer for core-insulated double walls with 440 mm wall thickness 3009277 GFRP spacer bar 500 mm profiled 12 mm Spacer for core-insulated double walls with 500 mm wall thickness Special lengths on request
GFRP spacer bar The GFRP spacer is a profiled rod made of glass fiber reinforced plastic (GFRP). The spacer guarantees dimensionally accurate production of core-insulated double walls. Due to the profiling, the rod achieves high pull-out and punch-through resistances. The ends of the rod are partially injected so that the ends are tapered, but the rod still has a centric bearing surface and thus does not buckle laterally. The centric loading means that the spacer does not deform in height and no oversize has to be planned. Furthermore, the taper at the end serves a quick and easy penetration into the fresh concrete, as larger aggregates are simply pushed aside. The surface visibility of the bars is almost non-existent due to the taper at the end. The bar has a high resistance to alkalis. Benefits energy efficient - thermal bridge free adjustment of wall thicknesses powerful - high tear-out and punching resistance due to profiling Cost-effective - low assembly costs due to quick and easy installation compatible - perfect complement to the ThermoPin® Applications core insulated double walls Residential & commercial construction, single or multi-storey Technical characteristics and variants of the GFRP spacer bar Art.-Nr. Product Diameter Description 3009225 GFRP spacer bar 300 mm profiled 12 mm Spacer for core-insulated double walls with 300 mm wall thickness 3009226 GFRP spacer bar 350 mm profiled 12 mm Spacer for core-insulated double walls with 350 mm wall thickness 3009224 GFRP spacer bar 360 mm profiled 12 mm Spacer for core-insulated double walls with 360 mm wall thickness 3009318 GFRP spacer bar 365 mm profiled 12 mm Spacer for core-insulated double walls with 365 mm wall thickness 3009223 GFRP spacer bar 400 mm profiled 12 mm Spacer for core-insulated double walls with 400 mm wall thickness 3009321 GFRP spacer bar 420 mm profiled 12 mm Spacer for core-insulated double walls with 420 mm wall thickness 3009276 GFRP spacer bar 440 mm profiled 12 mm Spacer for core-insulated double walls with 440 mm wall thickness 3009277 GFRP spacer bar 500 mm profiled 12 mm Spacer for core-insulated double walls with 500 mm wall thickness Special lengths on request
GFRP spacer bar The GFRP spacer is a profiled rod made of glass fiber reinforced plastic (GFRP). The spacer guarantees dimensionally accurate production of core-insulated double walls. Due to the profiling, the rod achieves high pull-out and punch-through resistances. The ends of the rod are partially injected so that the ends are tapered, but the rod still has a centric bearing surface and thus does not buckle laterally. The centric loading means that the spacer does not deform in height and no oversize has to be planned. Furthermore, the taper at the end serves a quick and easy penetration into the fresh concrete, as larger aggregates are simply pushed aside. The surface visibility of the bars is almost non-existent due to the taper at the end. The bar has a high resistance to alkalis. Benefits energy efficient - thermal bridge free adjustment of wall thicknesses powerful - high tear-out and punching resistance due to profiling Cost-effective - low assembly costs due to quick and easy installation compatible - perfect complement to the ThermoPin® Applications core insulated double walls Residential & commercial construction, single or multi-storey Technical characteristics and variants of the GFRP spacer bar Art.-Nr. Product Diameter Description 3009225 GFRP spacer bar 300 mm profiled 12 mm Spacer for core-insulated double walls with 300 mm wall thickness 3009226 GFRP spacer bar 350 mm profiled 12 mm Spacer for core-insulated double walls with 350 mm wall thickness 3009224 GFRP spacer bar 360 mm profiled 12 mm Spacer for core-insulated double walls with 360 mm wall thickness 3009318 GFRP spacer bar 365 mm profiled 12 mm Spacer for core-insulated double walls with 365 mm wall thickness 3009223 GFRP spacer bar 400 mm profiled 12 mm Spacer for core-insulated double walls with 400 mm wall thickness 3009321 GFRP spacer bar 420 mm profiled 12 mm Spacer for core-insulated double walls with 420 mm wall thickness 3009276 GFRP spacer bar 440 mm profiled 12 mm Spacer for core-insulated double walls with 440 mm wall thickness 3009277 GFRP spacer bar 500 mm profiled 12 mm Spacer for core-insulated double walls with 500 mm wall thickness Special lengths on request