BasicElast® 32 x 25 mm

InnoElast® Type 2 InnoElast® Type 2 is a 1-component, permanently elastic adhesive and sealant for highly stressed joints in the entire construction sector in accordance with DIN EN 15651-1. InnoElast® Type 2 adheres to many materials without primer and seals joints up to 4.80 m watertight under pressure. Product features 1-component adhesive and sealant Good spraying properties No primer required Can also be applied to damp substrates Can be applied from -3°C on ice-free surfaces Solvent and isocyanate free Very high initial adhesion even in fresh condition Weather and UV resistant Compatible with paints High chemical resistance Can be combined with other Elast products (bitumen compatible) Applications Adhesive and sealant for highly stressed joints in the entire construction sector (interior and exterior for concrete, wood and metal without primer). Permanently elastic sealant for facades and roofs according to DIN EN 15651 1. Waterproofing of basements and in civil engineering against pressing water, tested up to 4.80 m For repair and sealing of defects Adhesive for the ProElast® system Article data & delivery form InnoElast® Type II  5004115 - black in 600 ml tubular bag 5004247 - grey in 600 ml tubular bag (on request) 5004258 - grey in 400 ml tubular bag (on request) Surface preparation Substrates must be solid and load-bearing and free from dust, grease, oils and other separating materials. The substrate must be damp, but not wet with a visible film. Suitable substrates are concrete and other mineral building materials as well as, among others, plasterboard, wood, metals, PVC, ceramics, bitumen, etc. In case of doubt, we recommend a preliminary test. Processing InnoElast® is applied directly using a squeeze gun. Priming is not necessary with suitable substrates. For joint sealing, ensure a sufficiently wide (≥5 mm) and sufficiently deep (≥ 10 mm and ≥ ½Width) joint formation. A 3-flank adhesion to the joint base is to be prevented by inserting a suitable joint filling cord or a strip of polyethylene. It is recommended to tape the joint edges with adhesive tape. The sealant must be applied to the joint without voids or bubbles. A good bond with the joint edges must be achieved by pressing and smoothing. Pure liquid soaps (not diluted with water), e.g. washing-up liquid, are suitable as smoothing agents. Remove the adhesive tape immediately after smoothing. The maximum sealant thickness in one work step should not exceed 5 cm. When used as an adhesive, InnoElast® is applied evenly to the bonding surface and spread with a notched trowel in a layer thickness of 1 to 2 mm. Ensure that the bond is free of cavities and bubbles by pressing on the entire surface. Large-surface bonding with InnoElast® requires a moisture-permeable substrate. For impermeable substrates, we recommend the use of FlächenElast® adhesive and sealant with artificial hardener. For tight bonding of the ProElast® sheet, please observe the processing instructions in the "ProElast® System" data sheet. In cases of doubt regarding substrate preparation and processing, we recommend a preliminary test. Aftercare Protect InnoElast® from moisture during the period of stable skin formation. For subsequent painting, we recommend carrying out your own tests due to the wide range of possible painting systems. InnoElast® Type 2 is compatible with paint according to DIN 52452 Part 4.  

AgrarElast Driving silos of JGS plants and biogas plants have to be specially sealed due to the new AwSV regulation (regulation on plants handling substances hazardous to water, valid since 01.08.2017). For the renovation and new construction of facilities for the storage and filling of liquid manure, slurry and silage leachate (JGS) - mobile silos, fermentation feed silos and solid manure plates - as well as biogas plants, only construction products may be used that have the appropriate building authority approvals. In order to meet the high requirements for the permanent sealing of JGS plants, the joint sealant AgrarElast is subject to regular product monitoring and material testing. In addition, AgrarElast is a joint sealing system approved by the DIBt (German Institute for Construction Technology) (Z-74.62-176). The newly developed product from BT innovation can thus be reliably used for sealing joints in JGS and biogas plants. AgrarElast is a sealant for sealing microbiologically and acid contaminated joints, for areas with composting and fermentation processes. The system can be used to seal silos, warehouses, solid concrete manure slabs and asphalt. The system is suitable for movement joints and is characterized by high temperature resistance. The AgrarElast joint sealing system consists of AgrarElast joint sealant and primers A(sphalt) for asphalt and B(eton) for concrete. Primer A is suitable for asphalt, asphalt concrete and bitumen. This product is a set consisting of components A+B. The primer B is suitable for concrete, metal and glass, among others. Advantages of the joint sealant AgrarElast AgrarElast can be used to seal joint areas between concrete or asphalt. AgrarElast is also suitable for movement joints. The appropriate primers are required for pretreatment. Here are all the advantages of the joint sealant AgrarElast at a glance:   Sealing joints between concrete - concrete, asphalt - concrete and asphalt - asphalt Accessible / passable High allowable deformation of 12.5 Very high temperature resistance compared to sealants based on PU and bitumen Weathering and UV resistance Simple and safe processing Stable with only low shrinkage Approval (abZ: Z-74.62-176) from the German Institute for Building Technology (DIBt) Solvent-free, isocyanate-freeFor safe use, you are welcome to contact the BT technical staff, who will provide you with competent advice and instruction. Application and possible uses AgrarElast is used to seal storage and filling facilities with substances generally hazardous to water, e.g. in: JGS and biogas plants Solid manure plates Digestate silos Driving silos Wastewater systems The AgrarElast joint sealing system, with its approval number from Deutsches Institut für Bautechnik Z-74-62-176, has all the necessary verifications for these applications. Fields of application: Sealant for microbiologically contaminated joints For areas with composting and fermentation Joints that come into contact with acid Technical information: The AgrarElast is a 1-component, permanently elastic adhesive and sealant for highly stressed joints in the agricultural construction sector. Technical characteristics of the AgrarElast: Color black Hardness (Shore A type) 55 Allowable deformation 12.5 Temperature resistance -40 to +100°C Working temperature +5 to +35°C Tensile strength approx. 2.3 N/mm² Through-curing* approx. 3 mm/24h * measured at 23°C and 50 % rel. humidity   Primer A(sphalt) is a 2-component epoxy primer for the pretreatment of bituminous substrates when joint sealing with AgrarElast. As a pretreatment agent for asphalt surfaces, it is a component of the approved AgrarElast waterproofing system (approval Z 74.62-176).   Primer B(eton) is a 1-component primer for the pretreatment of various substrates when using the sealant AgrarElast. As a pretreatment agent for concrete surfaces, it is a component of the approved AgrarElast joint sealing system (approval Z 74.62-176). Observe the hazard and safety information on the Material Safety Data Sheets of the AgrarElast and the primers. Product features and variants of AgrarElast Art.-Nr. Article description Article information 5004273 AgrarElast 600ml / tubular bag; 15 bags/carton 5004275 AgrarElast Primer A(sphalt) 500 ml / set, consisting of component A + B 5004274 AgrarElast Primer B(eton) 500 ml / can